View ICX406AQ_1696357.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 1 ? e01327-ps sony reserves the right to change products and specifications without prior notice. this information does not convey any licens e by any implication or otherwise under any patents or other right. application circuits shown, if any, are typical examples illustr ating the operation of the devices. sony cannot assume responsibility for any problems arising out of the use of these circuits. ICX406AQ 20 pin dip (plastic) description the ICX406AQ is a diagonal 8.98mm (type 1/1.8) interline ccd solid-state image sensor with a square pixel array and 3.98m effective pixels. frame readout allows all pixels' signals to be output independently within approximately 1/3.33 second. also, number of vertical pixels decimation allows output of 30 frames per second in high frame rate readout mode. this chip features an electronic shutter with variable charge-storage time. r, g, b primary color mosaic filters are used as the color filters, and at the same time high sensitivity and low dark current are achieved through the adoption of super had ccd technology. this chip is suitable for applications such as electronic still cameras, etc. features ? supprots frame readout high horizontal and vertical resolution supports high frame rate readout mode: 30 frames/s, 25 frames/s, af1 mode: 60 frames/s, 50 frames/s, af2 mode: 120 frames/s, 100 frames/s square pixel horizontal drive frequency: 18mhz no voltage adjustments (reset gate and substrate bias are not adjusted.) r, g, b primary color mosaic filters on chip high sensitivity, low dark current continuous variable-speed shutter excellent anti-blooming characteristics exit pupil distance recommended range ?20 to ?100mm 20-pin high-precision plastic package device structure interline ccd image sensor total number of pixels: 2384 (h) 1734 (v) approx. 4.13m pixels number of effective pixels: 2312 (h) 1720 (v) approx. 3.98m pixels number of active pixels: 2308 (h) 1712 (v) approx. 3.95m pixels diagonal 8.980mm number of recommended recording pixels: 2272 (h) 1740 (v) approx. 3.87m pixels diagonal 8.875mm aspect ratio 4:3 chip size: 8.10mm (h) 6.64mm (v) unit cell size: 3.125m (h) 3.125m (v) optical black: horizontal (h) direction: front 16 pixels, rear 56 pixels vertical (v) direction: front 12 pixels, rear 2 pixels number of dummy bits: horizontal 28 vertical 1 (even fields only) substrate material: silicon diagonal 8.98mm (type 1/1.8) frame readout ccd image sensor with a square pixel for color cameras optical black position (top view) 2 12 v h pin 1 pin 11 56 16 ? super had ccd is a trademark of sony corporation. the super had ccd is a v ersion of son y's high performance ccd had (hole- accumulation diode) sensor with sharply improved sensitivity by the incorporation of a new semiconductor technology developed by sony corporation.
? 2 ? ICX406AQ 11 12 13 14 15 16 17 18 19 20 note) note) : photo sensor horizontal register vertical register v dd rg h 2 h 1 gnd sub c sub v l h 1 h 2 10 9 8 7 6 5 4 3 2 1 v out gnd test test v 1b v 1a v 2 v 3b v 3a v 4 b gr b gr b gb r gb r gb b gr b gr b gb r gb r gb gr r gr r block diagram and pin configuration (top view) pin no. symbol description pin no. symbol description 1 2 3 4 5 6 7 8 9 10 v 4 v 3a v 3b v 2 v 1a v 1b test test gnd v out vertical register transfer clock vertical register transfer clock vertical register transfer clock vertical register transfer clock vertical register transfer clock vertical register transfer clock test pin ? 1 test pin ? 1 gnd signal output 11 12 13 14 15 16 17 18 19 20 v dd rg h 2 h 1 gnd sub c sub v l h 1 h 2 supply voltage reset gate clock horizontal register transfer clock horizontal register transfer clock gnd substrate clock substrate bias ? 2 protective transistor bias horizontal register transfer clock horizontal register transfer clock pin description ? 1 leave this pin open. ? 2 dc bias is generated within the ccd, so that this pin should be grounded externally through a capacitance of 0.1f.
? 3 ? ICX406AQ absolute maximum ratings item v dd , v out , rg ? sub v 1a , v 1b , v 3a , v 3b ? sub v 2 , v 4 , v l ? sub h 1 , h 2 , gnd ? sub c sub ? sub v dd , v out , rg, c sub ? gnd v 1a , v 1b , v 2 , v 3a , v 3b , v 4 ? gnd h 1 , h 2 ? gnd v 1a , v 1b , v 3a , v 3b ? v l v 2 , v 4 , h 1 , h 2 , gnd ? v l voltage difference between vertical clock input pins h 1 ? h 2 h 1 , h 2 ? v 4 against sub against gnd against v l between input clock pins storage temperature guaranteed temperature of performance operating temperature ?40 to +12 ?50 to +15 ?50 to +0.3 ?40 to +0.3 ?25 to ?0.3 to +22 ?10 to +18 ?10 to +6.5 ?0.3 to +28 ?0.3 to +15 to +15 ?6.5 to +6.5 ?10 to +16 ?30 to +80 ?10 to +60 ?10 to +75 v v v v v v v v v v v v v c c c ? 1 ratings unit remarks ? 1 +24v (max.) when clock width < 10s, clock duty factor < 0.1%. +16v (max.) is guaranteed for turning on or off power supply.
? 4 ? ICX406AQ bias conditions supply voltage protective transistor bias substrate clock reset gate clock item v dd v l sub rg symbol 15.0 ? 1 ? 2 ? 2 min. v unit remarks typ. max. ? 1 v l setting is the v vl voltage of the vertical clock waveform, or the same voltage as the v l power supply for the v driver should be used. ? 2 do not apply a dc bias to the substrate clock and reset gate clock pins, because a dc bias is generated within the ccd. dc characteristics 14.55 15.45 supply current item i dd symbol 7.0 min. unit remarks typ. max. ma 10.0 3.0 clock voltage conditions item symbol min. typ. max. unit waveform diagram remarks readout clock voltage vertical transfer clock voltage horizontal transfer clock voltage reset gate clock voltage substrate clock voltage v vt v vh1 , v vh2 v vh3 , v vh4 v vl1 , v vl2 , v vl3 , v vl4 v v v vh3 ? v vh v vh4 ? v vh v vhh v vhl v vlh v vll v h v hl v cr v rg v rglh ? v rgll v rgl ? v rglm v sub 14.55 ?0.05 ?0.2 ?8.0 6.8 ?0.25 ?0.25 4.75 ?0.05 0.8 3.0 21.5 15.0 0 0 ?7.5 7.5 5.0 0 2.5 3.3 22.5 15.45 0.05 0.05 ?7.0 8.05 0.1 0.1 0.9 0.9 0.9 0.7 5.25 0.05 5.25 0.4 0.5 23.5 1 2 2 2 2 2 2 2 2 2 2 3 3 3 4 4 4 5 v vh = (v vh1 + v vh2 )/2 v vl = (v vl3 + v vl4 )/2 v v = v vh n ? v vl n (n = 1 to 4) high-level coupling high-level coupling low-level coupling low-level coupling cross-point voltage low-level coupling low-level coupling v v v v v v v v v v v v v v v v v v
? 5 ? ICX406AQ clock equivalent circuit constants c v1a , c v3a c v1b , c v3b c v2 , c v4 c v1a2 , c v3a4 c v1b2 , c v3b4 c v23a , c v41a c v23b , c v41b c v1a3a c v1b3b c v1a3b , c v1b3a c v24 c v1a1b , c v3a3b c h1 , c h2 c hh c rg c sub r 1a , r 1b , r 2 , r 3a , r 3b , r 4 r gnd r h symbol capacitance between vertical transfer clock and gnd capacitance between vertical transfer clocks capacitance between horizontal transfer clock and gnd capacitance between horizontal transfer clocks capacitance between reset gate clock and gnd capacitance between substrate clock and gnd vertical transfer clock series resistor vertical transfer clock ground resistor horizontal transfer clock series resistor item min. 1200 4700 3300 470 560 150 220 39 220 56 82 68 36 91 8 1000 62 18 15 typ. max. pf pf pf pf pf pf pf pf pf pf pf pf pf pf pf pf ? ? ? unit remarks vertical transfer clock equivalent circuit horizontal transfer clock equivalent circuit h 1 h 2 c h1 c h2 c hh r h r h h 1 h 2 r h r h r gnd c v1b3b r 1b c v41b v 1b c v4 c v41a c v1b c v1b3a c v1a1b c v1a c v1b2 r 1a v 1a c v1a2 v 2 r 2 c v24 c v1a3a c v23a c v23b r 3a v 3a c v2 c v3a c v3a3b c v1a3b c v3b r 3b v 3b c v3a4 c v3b4 v 4 r 4
? 6 ? ICX406AQ drive clock waveform conditions (1) readout clock waveform v vh = (v vh1 + v vh2 )/2 v vl = (v vl3 + v vl4 )/2 v v = v vh n ? v vl n (n = 1 to 4) (2) vertical transfer clock waveform 100% 90% 10% 0% tr tf 0v twh m 2 m v vt v vh1 v vhh v vhl v vh v vlh v vl1 v vll v vhl v vhh v vl v vh2 v vhh v vhh v vhl v vhl v vh v vlh v vl2 v vll v vl v vhh v vh v vlh v vll v vl v vhl v vl3 v vhl v vh3 v vhh v vh v vl v vhl v vlh v vll v vhl v vh4 v vhh v vhh v vl4 v 1a , v 1b v 3a , v 3b v 2 v 4
? 7 ? ICX406AQ v hl v cr twl two twh v h v h 2 tr h 2 90% 10% h 1 tf rg waveform v rglh v rgh v rgl v rgll v rglm tr twh twl tf v rg point a v sub (a bias generated within the ccd) 100% 90% 10% 0% tr tf twh m 2 m v sub (3) horizontal transfer clock waveform cross-point voltage for the h 1 rising side of the horizontal transfer clocks h 1 and h 2 waveforms is v cr . the overlap period for twh and twl of horizontal transfer clocks h 1 and h 2 is two. (4) reset gate clock waveform v rglh is the maximum value and v rgll is the minimum value of the coupling waveform during the period from point a in the above diagram until the rising edge of rg. in addition, v rgl is the average value of v rglh and v rgll . v rgl = (v rglh + v rgll )/2 assuming v rgh is the minimum value during the interval with twh, then: v rg = v rgh ? v rgl negative overshoot level during the falling edge of rg is v rglm . (5) substrate clock waveform
? 8 ? ICX406AQ spectral sensitivity characteristics (excludes lens characteristics and light source characteristics) clock switching characteristics (horizontal drive frequency: 18mhz) min. twh typ. max. min. typ. max. min. typ. max. min. typ. max. twl tr tf 3.10 14 14 7 1.6 3.33 19.5 19.5 10 3.56 14 14 19.5 19.5 37 0.5 8.5 8.5 4 14 14 0.5 15 0.5 8.5 8.5 5 250 14 14 0.5 unit s ns ns ns s remarks during readout when using cxd3400n tf tr ? 2ns during drain charge item readout clock vertical transfer clock horizontal transfer clock reset gate clock substrate clock symbol v t v 1a , v 1b , v 2 , v 3a , v 3b , v 4 h 1 h 2 rg sub min. two typ. max. 12 19.5 unit ns remarks item horizontal transfer clock symbol h 1 , h 2 400 1.0 b g r 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 450 500 550 wave length [nm] relative response 600 650 700
? 9 ? ICX406AQ image sensor characteristics (horizontal drive frequency: 18mhz) (ta = 25 c) item g sensitivity sensitivity comparison saturation signal smear video signal shading dark signal dark signal shading line crawl g line crawl r line crawl b lag symbol sg rr rb vsat sm shg vdt ? vdt lcg lcr lcb lag min. 180 0.35 0.40 380 ty p . 220 0.50 0.55 ? 85 ? 72 max. 285 0.65 0.70 ? 81.2 ? 68.0 20 25 16 8 3.8 3.8 3.8 0.5 unit mv mv db % mv mv % % % % measurement method 1 1 1 2 3 4 5 6 7 7 7 8 remarks 1/30s accumulation ta = 60 c frame readout mode ? 1 high frame rate readout mode zone 0 and i zone 0 to ii ' ta = 60 c, 3.33 frame/s ta = 60 c, 3.33 frame/s, ? 2 ? 1 after closing the mechanical shutter, the smear can be reduced to below the detection limit by performing vertical register sweep operation. ? 2 excludes vertical dark signal shading caused by vertical register high-speed transfer. 2 v 10 2 4 4 ignored region effective pixel region zone 0, i zone ii , ii ' v 10 h 8 h 8 2312 (h) 1720 (v) zone definition of video signal shading measurement system ccd c.d.s s/h s/h amp ccd signal output [ ? a] gr/gb channel signal output [ ? b] r/b channel signal output [ ? c] note) adjust the amplifier gain so that the gain between [ ? a] and [ ? b], and between [ ? a] and [ ? c] equals 1. r b
? 10 ? ICX406AQ image sensor characteristics measurement method measurement conditions (1) in the following measurements, the device drive conditions are at the typical values of the bias and clock voltage conditions, and the frame readout mode is used. (2) in the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical black level (ob) is used as the reference for the signal output, which is taken as the value of the gr/gb channel signal output or the r/b channnel signal output of the measurement system. color coding of this image sensor & readout the primary color filters of this image sensor are arranged in the layout shown in the figure on the left (bayer arrangement). gr and gb denote the g signals on the same line as the r signal and the b signal, respectively. for frame readout, the a1 and a2 lines are output as signals in the a field, and the b1 and b2 lines in the b field. gb b gb b rgrrgr gb b gb b rgrrgr b2 b1 a2 a1 horizontal register color coding diagram
? 11 ? ICX406AQ 2. frame readout mode, high frame rate readout mode frame readout mode high frame rate readout mode 1st field 2nd field 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 1 2 v out r gb r gb r gb r gb r gb r gb r gb r r gb gr b gr b gr b gr b gr b gr b gr b gr gr b 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 1 2 v out r gb r gb r gb r gb r gb r gb r gb r r gb gr b gr b gr b gr b gr b gr b gr b gr gr b 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 1 2 v out r gb r gb r gb r gb r gb r gb r gb r r gb gr b gr b gr b gr b gr b gr b gr b gr gr b readout modes 1. readout modes list mode name frame rate number of effective output lines frame readout mode high frame rate readout mode af1 mode af2 mode ntsc mode pal mode ntsc mode pal mode ntsc mode pal mode ntsc mode pal mode 3.33 frame/s 3.57 frame/s 30 frame/s 25 frame/s 60 frame/s 50 frame/s 120 frame/s 100 frame/s 1720 (odd 860, even 860) 1720 (odd 860, even 860) 215 215 97 119 35 46 note) blacked out portions in the diagram indicate pixels which are not read out. 1. frame readout mode in this mode, all pixel signals are divided into two fields and output. all pixel signals are read out independently, making this mode suitable for high resolution image capturing. 2. high frame rate readout mode output is performed at 30 frames per second by reading out 4 pixels for every 16 vertical pixels and adding 2 pixels in the horizontal ccd. the number of output lines is 215 lines. this readout mode emphasizes processing speed over vertical resolution.
? 12 ? ICX406AQ 3. af1 mode, af2 mode the af modes increase the frame rate by cutting out a portion of the picture through high-speed elimination of the top and bottom of the picture in high frame rate readout mode. af1 allows 1/60s and 1/50s output, and af2 allows 1/120s and 1/100s output, so these modes are effective for raising the auto focus (af) speed. number of effective lines in high frame rate readout mode 215 top frame shift region cut-out region bottom high-speed sweep region
? 13 ? ICX406AQ definition of standard imaging conditions (1) standard imaging condition i : use a pattern box (luminance: 706cd/m 2 , color temperature of 3200k halogen source) as a subject. (pattern for evaluation is not applicable.) use a testing standard lens with cm500s (t = 1.0mm) as an ir cut filter and image at f5.6. the luminous intensity to the sensor receiving surface at this point is defined as the standard sensitivity testing luminous intensity. (2) standard imaging condition ii : image a light source (color temperature of 3200k) with a uniformity of brightness within 2% at all angles. use a testing standard lens with cm500s (t = 1.0mm) as an ir cut filter. the luminous intensity is adjusted to the value indicated in each testing item by the lens diaphragm. (3)standard imaging condition iii : image a light source (color temperature of 3200k) with a uniformity of brightness within 2% at all angles. use a testing standard lens (exit pupil distance ? 33mm) with cm500s (t = 1.0mm) as an ir cut filter. the luminous intensity is adjusted to the value indicated in each testing item by the lens diagram. 1. g sensitivity, sensitivity comparison set to the standard imaging condition i . after setting the electronic shutter mode with a shutter speed of 1/100s, measure the signal outputs (v gr , v gb , v r and v b ) at the center of each gr, gb, r and b channel screen, and substitute the values into the following formulas. v g = (v gr + v gb ) /2 sg = v g [mv] rr = v r /v g rb = v b /v g 2. saturation signal set to the standard imaging condition ii . after adjusting the luminous intensity to 20 times the intensity with the average value of the gr signal output, 150mv, measure the minimum values of the gr, gb, r and b signal outputs. 3. smear set to the standard imaging condition ii . with the lens diaphragm at f5.6 to f8, first adjust the average value of the gr signal output to 150mv. measure the average values of the gr signal output, gb signal output, r signal output and b signal output (gra, gba, ra, ba), and then adjust the luminous intensity to 500 times the intensity with the average value of the gr signal output, 150mv. after the readout clock is stopped and the charge drain is executed by the electronic shutter at the respective h blankings, measure the maximum value (vsm [mv]) independent of the gr, gb, r and b signal outputs, and substitute the values into the following formula. sm = 20 log ( vsm ) [db] (1/10v method conversion value) 4. video signal shading set to the standard imaging condition iii . with the lens diaphragm at f5.6 to f8, adjusting the luminous intensity so that the average value of the gr signal output is 150mv. then measure the maximum value (grmax [mv]) and minimum value (grmin [mv]) of the gr signal output and substitute the values into the following formula. shg = (grmax ? grmin) /150 100 [%] 1 10 1 500 gra + gba + ra + ba 4 100 30
? 14 ? ICX406AQ 5. dark signal measure the average value of the signal output (vdt [mv]) with the device ambient temperature of 60 c and the device in the light-obstructed state, using the horizontal idle transfer level as a reference. 6. dark signal shading after measuring 5, measure the maximum (vdmax [mv]) and minimum (vdmin [mv]) values of the dark signal output and substitute the values into the following formula. ? vdt = vdmax ? vdmin [mv] 7. line crawl set to the standard imaging condition ii . adjusting the luminous intensity so that the average value of the gr signal output is 150mv, and then insert r, g and b filters and measure the difference between g signal lines ( ? glr, ? glg, ? glb [mv]) as well as the average value of the g signal output (gar, gag, gab). substitute the values into the following formula. lci = 100 [%] (i = r, g, b) 8. lag adjust the gr signal output value generated by the strobe light to 150mv. after setting the strobe light so that it strobes with the following timing, measure the residual signal amount (vlag). substitute the value into the following formula. lag = (vlag/150) 100 [%] light vd v1a/v1b strobe light timing output vlag (lag) gr signal output 150mv ? gli gai
? 15 ? ICX406AQ drive circuit notes) substrate bias control 1. the saturation signal level decreases when exposure is performed using the mechanical shutter, so control the substrate bias. 2. a saturation signal level equivalent to that for continuous exposure can be assured by connecting a 2.7k ? grounding registor to the ccd c sub pin. drive timing precautions 1. blooming occurs in modes (high frame rate readout, etc.) that do not use the mechanical shitter, so do not ground the connected 2.7k ? resistor. 2. tf is slow, so the internally generated voltage v sub may not drop to a sufficiently low level if the substrate bias control signal is not set to high level 10ms before entering the exposure period and the 2.7k ? resistor connected to the c sub pin is not grounded. 3. the blooming signal generated during exposure in mechanical shutter mode is swept by providing two fields or more of idle transfer through vertical register high-speed sweep transfer from the time the mechanical shutter closes until sensor readout is performed. however, note that the v l potential and the sub pin dc voltage sag at this time. substrate bias control signal v sub cont. mechanical shutter mode substrate bias sub pin voltage gnd tr 2ms tf 4ms internally generated value v sub xsub xv3 xsg3b xsg3a xv1 xsg1b xsg1a xv4 xv2 v sub cont. h 2 h 1 rg 0.1 0.1 0.1 0.1 200k 0.1 0.01 3.3/20v 0.1 4.7k 100k ccd out 2sc4250 vr1 (2.7k) 20 19 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 9 10 cxd3400n 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 icx406 (bottom view) 3.3/16v 1/35v 3.3v ?7.5v 15v h 2 rg gnd v dd h 2 h 1 v l c sub sub h 1 test gnd v out v 4 v 3a v 3b v 2 v 1a test v 1b
? 16 ? ICX406AQ drive timing chart (vertical sequence) high frame rate readout mode frame readout mode/electronic shutter normal operation note) the b output signal contain a blooming component and should therefore not be used. apply 20 or more electronic shutter pulses at the start of exposure for the recording image. if less than 20 pulses are applied , the electronic shutter may occur a discharge error. vd act. ccd out v1a sub trg mechanical shutter v sub cont. open open close v1b v3a v4 v2 v3b a b b d e c a signal output a signal output b signal output b signal output c signal output (odd) c signal output (even) output after frame readout d signal output e signal output high frame rate readout mode high frame rate readout mode exposure operation frame readout mode
? 17 ? ICX406AQ drive timing chart (vertical sync) ntsc/pal frame readout mode ntsc: 3.33 frame/s, pal: 3.57 frame/s note) the 1013h and 2026h horizontal period in ntsc mode are 1672clk, the 945h and 1890h horizontal period in pal mode are 464clk. hd exposure period all pixels output period vd 1720 1718 2 4 6 8 10 12 2 4 6 8 10 1 9 3 5 7 9 11 1 3 5 7 1719 1717 ccd out v4 v3a/v3b v1a/v1b v2 sub trg mechanical shutter v sub cont. open open 1014 2026 1 2 3 "a" "b" "c" 77 77 83 83 1890 1956 1888 1955 1887 1 2 3 946 1013 945 943 943 942 942 1023 955 1022 954 1088 1020 1090 1022 1096 1028 1086 1018 10 73 pa l 1 2 3 10 73 76 76 "c" 1 2 3 close ntsc
? 18 ? ICX406AQ drive timing chart (readout) ntsc/pal frame readout mode "a" enlarged 2669 1 60 317 1104 124 156 188 252 220 284 ntsc: #1088 pal: #1020 ntsc: #76 pal: #76 ntsc: #77 pal: #77 1168 1200 1260 1292 1136 317 v1a/v1b v2 v4 v2 v4 v3a/v3b v1a/v1b v3a/v3b h1 2669 1 60 ntsc: #1089 pal: #1021 1202 "b" enlarged
? 19 ? ICX406AQ drive timing chart (high-speed sweep operation) ntsc/pal frame readout mode "c" enlarged v1a/v1b v2 v3a/v3b v4 #1 #2 #3 #4 #1739 1 60 hd 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 28 194837clk = 73 lines
? 20 ? ICX406AQ drive timing chart (horizontal sync) ntsc/pal frame readout mode h1 h2 rg clk shd sub v2 129 1 65 96 96 32 1 1 1 1 1 1 96 160 1 1 97 1 33 1 85 160 64 1 1 108 1 64 shp v1a/v1b v3a/v3b v4 2669 ignored pixel 2 bits ignored pixel 2 bits 60 1 56 1 317 345 361 257 28 1 1 16 364 1 5 3
? 21 ? ICX406AQ drive timing chart (vertical sync) ntsc/pal high frame rate readout mode ntsc: 30 frame/s, pal: 25 frame/s note) the 226h and 225h horizontal period in ntsc mode are 1372clk, the 270h in pal mode is 2039clk. hd vd 1713 1706 1717 1710 5 10 21 14 37 30 53 46 69 62 85 78 94 1 6 1 17 10 33 26 49 42 65 58 81 74 90 1713 1706 1717 1710 5 10 21 14 37 30 53 46 69 62 85 78 94 1 6 1 17 10 33 26 49 42 65 58 81 74 90 ccd out v3a v3b v4 v2 v1a v1b 10 10 9 9 1 1 226 270 218 218 10 pa l "d" "d" 218 270 1 10 9 9 218 226 1 2 3 2 3 4 4 5 5 ntsc
? 22 ? ICX406AQ drive timing chart (readout) ntsc/pal high frame rate readout mode "d" enlarged 2669 1 60 317 60 60 84 #1 #2 1168 1104 1292 1356 1416 1260 1136 1202 1324 317 v1a v1b v2 v3b v4 v3a h1 2669 1 60 1200 1358 68 68 76
? 23 ? ICX406AQ drive timing chart (horizontal sync) ntsc/pal high frame rate readout mode, af1 mode, af2 mode h1 h2 rg clk shd sub v2 1 1 1 116 1 shp v1a/v1b v3a/v3b v4 2669 5 ignored pixel 2 bits ignored pixel 2 bits 60 1 56 1 317 345 361 257 28 1 1 16 364 1 8 124 1 40 124 1 40 124 133 17 25 85 9 40 124 1 24 124 1 40 124 1 40 124 1 40 124 1 40 124 1 40 124 1 40 124 40 1 1 40 1 124 1 40 124 1 40 1 164 1 24 40 1 108 3 1
? 24 ? ICX406AQ drive timing chart (vertical sync) ntsc/pal af1 mode ntsc: 60 frame/s, pal: 50 frame/s note) the 113h horizontal period in ntsc mode is 1372clk, the 135h horizongal period in pal mode is 2354clk. hd vd ccd out 465 474 481 490 469 478 485 494 465 474 481 490 469 478 485 494 10 6 1402 1406 1409 1413 10 6 pa l 465 474 481 490 469 478 485 494 465 474 481 490 469 478 485 494 10 6 1226 1230 1233 1237 10 6 ntsc v3a v3b v4 v2 v1a v1b 1 "e" "g" "f" 1 113 135 106 128 10 10 9 9 10 pa l 1 2 3 10 9 9 "f" "e" "g" 1 135 113 2 3 4 5 4 5 ntsc
? 25 ? ICX406AQ drive timing chart (vertical sync) ntsc/pal af2 mode ntsc: 120 frame/s, pal: 100 frame/s note) the 57h horizontal period in ntsc mode is 686clk, the 68h horizontal period in pal mode is 1177clk. hd vd ccd out 721 730 737 746 725 734 741 750 721 730 737 746 725 734 741 750 721 730 737 746 725 734 741 750 721 730 737 746 725 734 741 750 10 6 1073 1077 1082 1086 10 6 pa l 10 6 986 990 993 997 10 6 ntsc v3a v3b v4 v2 v1a v1b 1 "e" "i" "h" 1 57 68 47 58 10 10 9 9 10 pa l 1 2 3 10 9 9 "h" "e" "i" 1 68 57 2 3 4 5 4 5 ntsc
? 26 ? ICX406AQ drive timing chart (readout) ntsc/pal af1 mode, af2 mode 2669 1 60 317 60 60 84 1168 1104 1292 1488 1552 1496 1560 1480 1544 1356 1416 1260 1456 1520 1136 1202 1324 1472 1536 317 v1a v1b v2 v3b v4 v3a h1 2669 1 60 1200 1358 1504 1568 1464 1528 1448 1512 68 68 76 "e" enlarged
? 27 ? ICX406AQ drive timing chart ntsc/pal af1 mode "f" enlarged v1a/v1b v2 v3a/v3b v4 #2 #3 #4 #228 1 60 hd 8 8 8 8 8 8 8 8 16014clk = 6 lines #1
? 28 ? ICX406AQ drive timing chart ntsc/pal af1 mode "g" enlarged v1a/v1b v2 v3a/v3b v4 #2 #3 #4 #244 1 60 hd 8 8 8 8 8 8 8 8 16014clk = 6 lines #1 ntsc: 107h pal: 129h ntsc: 113h pal: 135h ntsc: 1h pal: 1h
? 29 ? ICX406AQ drive timing chart ntsc/pal af2 mode "h" enlarged v1a/v1b v2 v3a/v3b v4 #2 #3 #4 #356 1 60 hd 8 8 8 8 8 8 8 8 24021clk = 9 lines #1
? 30 ? ICX406AQ drive timing chart ntsc/pal af2 mode "i" enlarged v1a/v1b v2 v3a/v3b v4 #2 #3 #4 #364 1 60 hd 8 8 8 8 8 8 8 8 24021clk = 9 lines #1 ntsc: 48h pal: 59h ntsc: 57h pal: 68h ntsc: 1h pal: 1h
? 31 ? ICX406AQ notes on handling 1) static charge prevention ccd image sensors are easily damaged by static discharge. before handling be sure to take the following protective measures. a) either handle bare handed or use non-chargeable gloves, clothes or material. also use conductive shoes. b) when handling directly use an earth band. c) install a conductive mat on the floor or working table to prevent the generation of static electricity. d) ionized air is recommended for discharge when handling ccd image sensors. e) for the shipment of mounted substrates, use boxes treated for the prevention of static charges. 2) soldering a) make sure the package temperature does not exceed 80 c. b) solder dipping in a mounting furnace causes damage to the glass and other defects. use a ground 30w soldering iron and solder each pin in less than 2 seconds. for repairs and remount, cool sufficiently. c) to dismount an image sensor, do not use a solder suction equipment. when using an electric desoldering tool, use a thermal controller of the zero-cross on/off type and connect it to ground. 3) dust and dirt protection image sensors are packed and delivered by taking care of protecting its glass plates from harmful dust and dirt. clean glass plates with the following operations as required, and use them. a) perform all assembly operations in a clean room (class 1000 or less). b) do not either touch glass plates by hand or have any object come in contact with glass surfaces. should dirt stick to a glass surface, blow it off with an air blower. (for dirt stuck through static electricity ionized air is recommended.) c) clean with a cotton bud and ethyl alcohol if grease stained. be careful not to scratch the glass. d) keep in a case to protect from dust and dirt. to prevent dew condensation, preheat or precool when moving to a room with great temperature differences. e) when a protective tape is applied before shipping, just before use remove the tape applied for electrostatic protection. do not reuse the tape. 4) installing (attaching) a) remain within the following limits when applying a static load to the package. do not apply any load more than 0.7mm inside the outer perimeter of the glass portion, and do not apply any load or impact to limited portions. (this may cause cracks in the package.) plastic package cover glass compressive strength 50n 50n 1.2nm torsional strength b) if a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. therefore, for installation, use either an elastic load, such as a spring plate, or an adhesive.
? 32 ? ICX406AQ the cross section of lead frame can be seen on the side of the package for structure a. structure a structure b chip metal plate (lead frame) package cross section of lead frame c) the adhesive may cause the marking on the rear surface to disappear, especially in case the regulated voltage value is indicated on the rear surface. therefore, the adhesive should not be applied to this area, and indicated values should be transferred to other locations as a precaution. d) the notch of the package is used for directional index, and that can not be used for reference of fixing. in addition, the cover glass and seal resin may overlap with the notch of the package. e) if the leads are bent repeatedly and metal, etc., clash or rub against the package, the dust may be generated by the fragments of resin. f) acrylate anaerobic adhesives are generally used to attach ccd image sensors. in addition, cyano- acrylate instantaneous adhesives are sometimes used jointly with acrylate anaerobic adhesives. (reference) 5) others a) do not expose to strong light (sun rays) for long periods, as color filters will be discolored. when high luminous objects are imaged with the exposure level controlled by the electronic iris, the luminance of the image-plane may become excessive and discoloring of the color filter will possibly be accelerated. in such a case, it is advisable that taking-lens with the automatic-iris and closing of the shutter during the power-off mode should be properly arranged. for continuous using under cruel condition exceeding the normal using condition, consult our company. b) exposure to high temperature or humidity will affect the characteristics. accordingly avoid storage or usage in such conditions. c) brown stains may be seen on the bottom or side of the package. but this does not affect the ccd characteristics. d) this package has 2 kinds of internal structure. however, their package outline, optical size, and strength are the same.
? 33 ? ICX406AQ package outline unit: mm sony corporation 20 pin dip b ~ b ' m a 1 1 c h v d 12.2 package structure package material lead treatment lead material package mass drawing number plastic gold plating 42 alloy as-b6-02(e) 0.95g 1. ?a? is the center of the effective image area. 2. the two points ?b? of the package are the horizontal reference. the point ?b'? of the package is the vertical reference. 3. the bottom ?c? of the package, and the top of the cover glass ?d? are the height reference. 4. the center of the effective image area relative to ?b? and ?b'? is (h, v) = (6.9, 6.0) ?0.075mm. 5. the rotation angle of the effective image area relative to h and v is ?1?. 6. the height from the bottom ?c? to the effective image area is 1.41 ?0.10mm. the height from the top of the cover glass ?d? to the effective image area is 1.49 ?0.15mm. 7. the tilt of the effective image area relative to the bottom ?c? is less than 50?. the tilt of the effective image area relative to the top ?d? of the cover glass is less than 50?. 8. the thickness of the cover glass is 0.5mm, and the refractive index is 1.5. 9. the notches on the bottom of the package are used only for directional index, they must not be used for reference of fixing. ~ ~ 0.25 1.7 1.7 1.7 11 20 1.7 10 12.0 ?0.1 2.9 ?0.15 3.5 ?0.3 13.8 ?0.1 12.7 10 20 11 6.9 10.9 0? to 9? 6.0 2.4 0.5 0.8 2.5 9.0 2.5 0.5 0.8 1.27 0.3 0.3 10.0 2.5

▲Up To Search▲

Price & Availability of ICX406AQ

	To Download ICX406AQ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .